Bandwidth : 30MHz - 125MHz
Sample rate : 250MS/s - 1GS/s
100K record length (10M optional, SDS5032E excluded)
Ultra-thin body
8 inch high def TFT display
Pass / Fail function
Add / Remove measure function,
User-defined measurement menu

Application

electronic circuit debugging
circuit testing
design and manufacture
education and training
automobile maintenance and testing

Model		SDS5032E	SDS6062E	SDS7072E	SDS7102E	SDS7122E
Bandwidth		30MHz	60MHz	70MHz	100MHz	125MHz
Sample Rate (real time)		250MS/s	500MS/s	1GS/s
Horizontal Scale (s/div)		4ns/div~100s/div, step by 1~2~4	5ns/div - 100s/div, step by 1 - 2 - 5	2ns/div - 100s/div, step by 1 - 2 - 5
Rise Time (at input, typical)		≤11ns
Channel		2 + 1 (external)
Display		8" color LCD, TFT display , 800 × 600 pixels, 65535 colors
Input Impedance		1MΩ ± 2%, in parallel with 15pF±5pF
Channel Isolation		50Hz : 100 : 1, 10MHz : 40 : 1
Max Input Voltage		400V (PK - PK) (DC+AC, PK - PK)
DC Gain Accuracy		±3%
Record Length		10K	100K (optional 10M)
DC Accuracy (average)		Average≥16:±(3% reading + 0.05 div) for ?V
Probe Attenuation Factor		1X, 10X, 100X, 1000X
LF Respond (AC, -3dB)		≥10Hz (at input, AC coupling, -3dB)
Sample Rate / Relay Time Accuracy		±100ppm
Interpolation		sin (x) / x
Interval (Delta T) Accuracy (full bandwidth)		Single : ±(1 interval time + 100ppm × reading + 0.6ns), Average>16 : ±(1 interval time + 100ppm × reading + 0.4ns)
Input Coupling		DC, AC , and GND
Vertical Resolution (A/D)		8 bits resolution (2 Channels simultaneously)
Vertical Sensitivity		5mV/div~10V/div (at input)	2mV/div~10V/div (at input)
Trigger Type		Edge, Pulse, Video, Slope	Edge, Pulse, Video, Slope, Alternate
Trigger Mode		Auto, Normal, Single
Trigger Level		±6 divisions from screen center
Line / Field Frequency (video)		NTSC, PAL, and SECAM standard
Cursor Measurement		?V, and ?T between cursors
Automatic Measurement		Vpp, Vavg, Vamp, Vrms, Freq, Period, Vmax, Vmin, Vtop, Vbase, Overshoot, Preshoot, Rise Time, Fall Time, Delay A→B↑, Delay A→B↓, +Width, -Width, +Duty, -Duty
Waveform Math		+, -, ×, ÷, FFT
Waveform Storage		15 waveforms
Lissajous Figure	Bandwidth	Full bandwidth
	Phase Difference	±3 degrees
Communication Interface		USB, USB flash disk storage, Pass / Fail, LAN, VGA (optional)
Cymometer		available
Power Supply		100V - 240V AC, 50/60Hz, CAT II
Power Consumption		<18W
Fuse		2A, T class, 250V
Battery		not supported
Dimension (W×H×D)		348 × 170 × 78 (mm)
Weight (without package)		1.50 kg

Oscilloscope kategorisine ait diğer ürünler

Owon TDS Series Touch Screen Digital Oscilloscope

- Max 200MHz bandwidth, up to 2GS/s realtime sample rate
- 7.6M record length
- 50,000 wfms/s waveform capture rate
- waveform zooming (horizontal / vertical), and saving
- FFT points (length, and resolution variable)
- multi-window extension
- user-friendly voice warning
- 8 inch 800 x 600 pixels high def LCD
- multi- communication interface : USB, VGA, LAN

Application

electronic circuit debugging
circuit testing
design and manufacture
education and training
automobile maintenance and testing

Model		TDS7104	TDS8104	TDS8204
Bandwidth		100MHz		200MHz
Channel		4
Sample Rate		1GS/s	2GS/s
Waveform Capture Rate		50,000 wfms/s
Display		8" touch screen color LCD
Input Coupling		DC, AC, and GND
Input Impedance		1MΩ ± 2%, in parallel with 10pF ± 5pF ; 50Ω ± 1%
Probe Attenuation Factor		1X, 10X, 100X, 1000X
Max Input Voltage		1MΩ input impedance : 400V (PK - PK) (DC + AC, PK - PK) ; 50Ω input impedance : 5V (PK - PK) (DC + AC, PK - PK)
Channel Isolation		50Hz:100:1 ; 10MHz:40:1
Interpolation		sin(x)/x
Record Length		7.6M
Horizontal Scale (s/div)		2ns/div - 100s/div, step by 1 - 2 - 5
Interval (Delta T) Accuracy (full bandwidth)		Single : ±(1 interval time + 100ppm × reading + 0.6ns), Average>16 : ±(1 interval time + 100ppm × reading + 0.4ns)
Vertical Resolution (A/D)		8 bits resolution (4 channels simultaneously)
Vertical Sensitivity		2mV/div - 10V/div (at input)
Analog Bandwidth		100MHz		200MHz
LF Respond (AC, -3dB)		≥10Hz (at input, AC coupling, -3dB)
Rise Time		≤3.5ns		≤1.7n
DC Accuracy		±3%
Trigger Type		Edge, Pulse, Video, Slope
Trigger Mode		Auto, Normal, Single
Trigger Level Range		±6 div from the screen center
Trigger level Accuracy (typical)		±0.3 div
Line / Field Frequency (video)		NTSC, PAL, and SECAM standard
Automatic Measurement		Vpp, Vavg, Vamp, Vrms, Freq, Period, Vmax, Vmin, Vtop, Vbase, Overshoot, Preshoot, Rise Time, Fall Time, Delay A→B↑, Delay A→B↓, +Width, -Width, +Duty, -Duty
Waveform Math		+, -, ×, ÷, FFT
Waveform Storage		4 reference waveforms
Lissajous Figure	Bandwidth	full Bandwidth
	Phase Difference	±3 degrees
Cursor Measurement		Delta V, and Delta T between cursors
Communication Port		USB host, USB device, VGA, LAN, AUX
Power Supply		100 - 240 V AC, 50/60Hz, CAT II
Dimension (W×H×D)		380 × 180 × 115 (mm)
Weight (without package)		1.5 kg

OWON, OSILOSKOP, OSCILLOSCOPE, TEKTRONIX, LECROY, KEYSIGHT, FLUKE, YOKOGAWA

Owon SDS E Series Digital Oscilloscope

Application

electronic circuit debugging
circuit testing
design and manufacture
education and training
automobile maintenance and testing

Model		SDS5032E	SDS6062E	SDS7072E	SDS7102E	SDS7122E
Bandwidth		30MHz	60MHz	70MHz	100MHz	125MHz
Sample Rate (real time)		250MS/s	500MS/s	1GS/s
Horizontal Scale (s/div)		4ns/div~100s/div, step by 1~2~4	5ns/div - 100s/div, step by 1 - 2 - 5	2ns/div - 100s/div, step by 1 - 2 - 5
Rise Time (at input, typical)		≤11ns
Channel		2 + 1 (external)
Display		8" color LCD, TFT display , 800 × 600 pixels, 65535 colors
Input Impedance		1MΩ ± 2%, in parallel with 15pF±5pF
Channel Isolation		50Hz : 100 : 1, 10MHz : 40 : 1
Max Input Voltage		400V (PK - PK) (DC+AC, PK - PK)
DC Gain Accuracy		±3%
Record Length		10K	100K (optional 10M)
DC Accuracy (average)		Average≥16:±(3% reading + 0.05 div) for ?V
Probe Attenuation Factor		1X, 10X, 100X, 1000X
LF Respond (AC, -3dB)		≥10Hz (at input, AC coupling, -3dB)
Sample Rate / Relay Time Accuracy		±100ppm
Interpolation		sin (x) / x
Interval (Delta T) Accuracy (full bandwidth)		Single : ±(1 interval time + 100ppm × reading + 0.6ns), Average>16 : ±(1 interval time + 100ppm × reading + 0.4ns)
Input Coupling		DC, AC , and GND
Vertical Resolution (A/D)		8 bits resolution (2 Channels simultaneously)
Vertical Sensitivity		5mV/div~10V/div (at input)	2mV/div~10V/div (at input)
Trigger Type		Edge, Pulse, Video, Slope	Edge, Pulse, Video, Slope, Alternate
Trigger Mode		Auto, Normal, Single
Trigger Level		±6 divisions from screen center
Line / Field Frequency (video)		NTSC, PAL, and SECAM standard
Cursor Measurement		?V, and ?T between cursors
Automatic Measurement		Vpp, Vavg, Vamp, Vrms, Freq, Period, Vmax, Vmin, Vtop, Vbase, Overshoot, Preshoot, Rise Time, Fall Time, Delay A→B↑, Delay A→B↓, +Width, -Width, +Duty, -Duty
Waveform Math		+, -, ×, ÷, FFT
Waveform Storage		15 waveforms
Lissajous Figure	Bandwidth	Full bandwidth
	Phase Difference	±3 degrees
Communication Interface		USB, USB flash disk storage, Pass / Fail, LAN, VGA (optional)
Cymometer		available
Power Supply		100V - 240V AC, 50/60Hz, CAT II
Power Consumption		<18W
Fuse		2A, T class, 250V
Battery		not supported
Dimension (W×H×D)		348 × 170 × 78 (mm)
Weight (without package)		1.50 kg

Owon MSO Series LA + Digital Oscilloscope

- 2 in 1 (DSO + LA)
- 8 inch color LCD
- USB data transmission supported
- 20 group automatic measurement options

Digital Storage Oscilloscope

- Bandwidth : 60MHz - 200MHz
- Sample rate : up to 2GS/s
- Auto-scale function
- FFT

Logic Analyzer

- Bandwidth : 100MHz - 200MHz
- Sample rate : 20S/s - 2GS/s
- 16 digital channels

Application

design and debug
circuit function test
identified signals logic information
education and training
mixed signal circuit test

Model		MSO5022S	MSO7062TD	MSO7102TD	MSO8102T	MSO8202T
Bandwidth		25MHz	60MHz	100MHz	100MHz	200MHz
Sample Rate (real time)		100MS/s	1GS/s	1GS/s	2GS/s
Rise Time		≤14ns	≤5.8ns	≤3.5ns		≤1.7ns
Display		7.8'' color LCD	8.0'' color LCD , TFT screen, 640 × 480 pixels
Channel		dual + external trigger
Horizontal Scale (s/div)		5ns/div - 5s/div, step by 1 - 2.5 - 5	2ns/div - 100s/div, step by 1 - 2 - 5			1ns/div - 100s/div, step by 1 - 2 - 5
DC Accuracy (average)		average>16 : ±(3% reading + 0.05div) for ?V
Vertical Sensitivity		5mV/div - 5V/div	2mV/div - 10V/div
DC Gain Accuracy		±3%
Vertical Resolution (A/D)		8 bits (2 channels simultaneously)
Interpolation		sin (x) / x
Max Input Voltage		300V (DC + AC, PK - PK)	400V (DC + AC, PK - PK )
Probe Attenuation Factor		1X,10X,100X,1000X
Trigger Mode		Edge, Video, Alternate, Pulse, Slope
Acquisition Mode		Normal, Peak Detect, and Average
Record Length		max 6K points	max 2M points
Waveform Storage		4 waveforms
Automatic Measurement		Vpp, Vavg, Vamp, Vrms, Freq, Period, Vmax, Vmin, Vtop, Vbase, Overshoot, Preshoot, Rise Time, Fall Time, Delay A→B↑, Delay A→B↓, +Width, -Width, +Duty, -Duty
Waveform Math		+, -, ×, ÷, FFT
Power Supply		100 - 240V AC, 50Hz / 60Hz, CAT?
Lissajou’s Figure	Bandwidth	25MHz	60MHz	100MHz		200MHz
	Phase Difference	±3 degrees
Communication Interface		USB1.1, and RS232	USB2.0, USB host, and RS232 / VGA (optional)
Fuse		1A, T class, 250V
Dimensions (W × H × D)		370 × 180 × 120 (mm)
Weight (without package)		2.20 kg

Logic Analyzer - Performance Specifications

Model	MSO5022S	MSO7062TD	MSO7102TD	MSO8102T	MSO8202T
Sample Rate (real time)	20S/s - 200MS/s	20S/s - 2GS/s
Bandwidth	40MHz	100MHz			200MHz
Channel	16
Record Length	Max 4M each channel
Input Impedance	660KΩ ± 5%, in parallel with 15 ± 5pF
Trigger Mode	Edge, Bus, State, Data Alignment, Data Width, Distributed Queue
Trigger Position Setting	Pre-trigger, Mid-trigger, and Re-trigger
Threshold Voltage	±6V (4 settings)
Input Signal Range	±30V
Data Search	available
Data System	binary, decimal, hex
Digital Filter	0, 1, 2 optional
Setting Storage	10 settings
USB Flash Disk Storage	available

Micsig MS300 Series Isolated Channel Scopemeter

MS300 series handheld multi-function oscilloscope,whose bandwidth ups to 100~200MHz, sampling rate is 1GS/s, Memory depth is 240k. With the 5.7 inch large LCD screen, the instrument possesses the performance which desktop oscilloscope can not match at the same time without the complex operation panel of desktop ones. It provides the functions of fully featured Oscilloscope, Multimeter and Data Logger. It is widely uses for Equipment maintenance, aviation, R&D, automated industry, process controlling.

Model	Bandwidth	Real time Sample Rate	Rise Time	Memory Depth	Channel	Touch operation	Serial bus trigger	Max waveform capture
MS310IT	100MHz	1GSa/s	≤3.5ns	240Kpts	2CH	YES	YES	-(can be upgraded to 50K wfms/s)
MS320IT	200MHz	1GSa/s	≤1.75ns	240Kpts	2CH	YES	YES	-(can be upgraded to 50K wfms/s)

Model	MS310IT	MS320IT
Bandwidth (BW)	100MHz	200MHz
Rise time	≤3.5ns	≤1.75ns
Real time sampling rate	single channel :1GSa/s,dual-channels:500MSa/s
Memory depth	single channel :240Kpts,dual-channels:120Kpts
Isolated channel	support
Max waveform capture rate	-(can be upgraded to 50K wfms/s)
Serial bus decode	Optional
Vertical system
Channels	2 oscilloscope channels,1 multimeter channel
Limited bandwidth	20MHz
Coupling modes	DC,AC,GND
Inputs impedance	parallel 1MΩ±1% with 15pF±3pF
Vertical sensitivity	5mV/div~50V/div
Vertical resolution	8bits
Max voltage input	600V CAT ? 300V CAT ?
Floating voltage from CHs to GND	1000V CAT ? 600V CAT ?
DC vertical gain accuracy	5mV/div~50V/div,2.0%
Horizontal system
Timebase	4ns/div~10s/div
Timebase delay range	-12divs~50s
Timebase accuracy	20ppm
Sample mode	normal,average, pk-pk,envelope
Dynamic record	- (can be upgraded)
Store waveform	4 ref waveforms (can be upgraded to flash disk storage)
Trigger system
Trigger types	edge, pulse, logic, serial bus(UART,LIN,CAN,SPI,I2C)
Trigger coupling	DC,AC,High-frequency suppression,Low-frequency suppression, Noise suppression
Trigger modes	auto, normal, single
Trigger source	CH1,CH2
Inhibition range	200ns~10s
Measurement
Automatic measurements	31 types
Cursor types	horizontal cursor, vertical cursor, cross cursor
Math
Operator	+ , - , * , /
FFT window settings	Rectangular, Hamming, Blackman-Harris, Hanning
Display Features
Screen	5.7 inch TFT LCD touch screen
Resolution	640*480
3D waveform display	not support
Grid of waveform display zone	horizontal 12 divs *vertical 8 divs
Form	YT form (can be upgraded to XY form)
Persist	auto, 100ms~10s or ∞
I/O Port
Mini USB2.0	connect to PC
USB2.0	connect to flash disk
WIFI	not support
Multimeter
Measurement types	10 physical measurements ,such as voltage, current, resistance, capacitance, diode , etc
Measurement accuracy	4 bits
Measurement display	max, average, min, values with time stamp,relative measurement
Data Logger
Logger content	multimeter measurements, oscilloscope waveform, oscilloscope measurements
Logger timebase	multimeter measurements,10s/div ~ 20min/div; oscilloscope measurements 10s/div ~ 20min/div oscilloscope waveform 100us/div ~ 2min/div
Logger time length	max 17 days (can be upgraded to flash disk record)
Power
Power adapter	input:100-240VAC,50-60Hz,2A; output:12VDC,5A
Battery	capacity:7.4V/6000mAh, work time:4~5 hours
Work environment
Temperature	-20? ~ +50?
Humidity	< 85%RH
Dimension
Size	254mm160mm60mm
Weight	main unit: 1380g (no battery), accessories(standard): 691g,battery(standard): 276g.

Micsig MS200 Series Scopemeter

Micsig MS200 Series allows moving the waveform and zooming in and out in three ways: using the buttons, using the scroll wheel or using touch screen.The Micsig software, ScopeSuite, has functions including updating, real time control, measurement, storage, dynamic display, record and data analysis. The MS200 Series has a 5.7" TFT LCD touch screen with 640×480 resolution.
FEATURES
3 control modes: touch, button, scroll wheel
?240Kpts memory depth
640*480 screen resolution
31 auto measurements
Cursor measurements
3 record modes: multimeter, oscilloscope, and oscilloscope waveform
multimeter is capable of conducting 10 measurements and tests such as AC/DC voltage, current, resistance, etc.
ScopeSuite software

Model	Bandwidth	Real time sample rate	Rise time	Memory depth	Channel	Touch operation	Series bus trigger
MS207T	70MHz	1GSa/s	≤5ns	240Kpts	2CH	YES	YES
MS210T	100MHz	1GSa/s	≤3.5ns	240Kpts	2CH	YES	YES
MS215T	150MHz	1GSa/s	≤2.33ns	240Kpts	2CH	YES	YES
MS220T	200MHz	1GSa/s	≤1.75ns	240Kpts	2CH	YES	YES

Three operation modes for moving waveform, zooming in and out, and using menu by touch,button and scroll wheel.

A perfect eye pattern contains an immense amount of parametric information about a signal, it gives you a visual indication of overall signal quality, noise level and signal jitter without looking at the data content. it finds errors like improper cable connections, bad contacts,incorrect grounding and missing or superfluous terminators. Serial bus trigger can be set to a variety of trigge conditions, users can find the wanted frame directly, reducing lots of their working loads.


240Kpts memory depth		The ScopeSuite of Micsig's software functions include updating, real time control, measurement, storage, dynamic display, record and data analysis.


640 * 480 high resolution		Persistance function keeps the abnormal signal stay longer and easy for analysis


Indoor mode		Outdoor mode


31 auto measurements		Horizontal cursor, vertical cursor, cross cursor


3 types of record modes: multimeter record,oscilloscope measurement record and oscilloscope waveform record.		10 physical measurements such as AC/DC voltage, current, resistance etc.

Model	MS207T	MS210T	MS215T	MS220T
Bandwidth (BW)	70MHz	100MHz	150MHz	200MHz
Rise time	≤5ns	≤3.5ns	≤2.33ns	≤1.75ns
Real time sampling rate	single channel :1GSa/s,dual-channels:500MSa/s
Memory depth	single channel :240Kpts,dual-channels:120Kpts
Isolated channel	not support
Max waveform capture rate	-(can be upgraded to 50K wfms/s)
Serial bus trigger	support
Vertical system
Channels	2 oscilloscope channels,1 multimeter channel
Limited bandwidth	20MHz
Coupling modes	DC,AC,GND
Input impedance	parallel 1MΩ±1% with 15pF±3pF
Vertical scale	5mV/div~50V/div
Vertical resolution	8bits
Max voltage input	600V CAT II 300V CAT III
DC vertical gain accuracy	5mV/div~50V/div, 2.0%
Horizontal system
Timebase	4ns/div~10s/div
Timebase delay range	-12divs~50s
Timebase accuracy	20ppm
Sample mode	normal,average, pk-pk,envelope
Dynamic record	- (can be upgraded)
Store waveform	4 ref waveforms (can be upgraded to flash disk storage)
Trigger system
Trigger types	edge, pulse, logic, serial bus(UART,LIN,CAN,SPI,I2C)
Trigger coupling	DC,AC,High-frequency suppression,Low-frequency suppression, Noise suppression
Trigger modes	auto, normal, single
Trigger scource	CH1,CH2
Inhibition range	200ns~10s
Measurement
Automatic measurements	31 types
Cursor types	horizontal cursor, vertical cursor, cross cursor
Math
Operator	+ , - , * , /
FFT window settings	Rectangular, Hamming, Blackman-Harris, Hanning
Display Features
Screen	5.7 inch TFT LCD touch screen
Resolution	640*480
3D waveform display	not support
Grid of waveform display zone	horizontal 12 divs *vertical 8 divs
Form	YT form (can be upgraded to XY form)
Persist	auto, 100ms~10s or ∞
I/O Port
Mini USB2.0	connect to PC
USB2.0	connect to flash disk
WiFi	not support
Multimeter
Measurement types	10 physical measurements ,such as voltage, current, resistance, capacitance, diode , etc
Measuremet accuracy	4 bits
Measurement display	max, average, min, values with time stamp,relative measurement
Data Logger
Logger content	multimeter measurements, oscilloscope waveform, oscilloscope measurements
Logger timebase	multimeter measurements,10s/div ~ 20min/div; oscilloscope measurements 10s/div ~ 20min/div oscilloscope waveform 100us/div ~ 2min/div
Logger time length	max 17 days (can be upgraded to flash disk record)
Power
Power adapter	input:100-240VAC,50-60Hz,2A; output:12VDC,5A
Battery	capacity:7.4V/6000mAh, work time:4~5 hours
Work environment
Temperature	-20°C ~ +50°C
Humidity	< 85%RH
Dimension
Size	254mm160mm60mm
Weight	main unit: 1380g (no battery), accessories(standard): 691g,battery(standard): 276g.

Micsig MS500 Series Isolated Channel Scopemeter

MS500 Series Handheld Multi-function Oscilloscopes provide the bandwidth of 100MHz or 200MHz, real-time sampling rate of 1GS/s and memory depth of 240k. The oscilloscopes come with 190k wfrms/s waveform refresh rate. Not only do the instruments have the function of Oscilloscope, but also functions of Multimeter, Data Logger and Serial Bus Analyzer. They can substitute for desktop oscilloscope with the same bandwidth completely, and have performance and benefits which desktop oscilloscope can not match. The instruments are the ideal choice for electric power, electron, auto, aviation, science, military industry, education and mining establishments. They will provide you service of more quality and more convenient.

Model	Bandwidth	Real time sampling rate	Rise time	Memory depth	Max capture rate	Channel	Touch operation	Serial bus trigger	Serial bus decode
MS510IT	100MHz	1GSa/s	≤3.5ns	240Kpts	190,000wfms/s	2CH	YES	YES	NO
MS510S	100MHz	1GSa/s	≤3.5ns	240Kpts	190,000wfms/s	2CH	YES	YES	YES
MS520IT	200MHz	1GSa/s	≤1.75ns	240Kpts	190,000wfms/s	2CH	YES	YES	NO
MS520S	200MHz	1GSa/s	≤1.75ns	240Kpts	190,000wfms/s	2CH	YES	YES	YES

Three isolated inputs include two oscilloscope inputs and one multimeter input, and all isolated inputs allow independent floating measurements with each input.

Three operation modes for moving waveform, zooming in and out, and using menu by touch, button and scroll wheel.


I2C serial bus decoding graphic mode		I2C serial bus decoding text mode

micsig oscilloscope ???

Waveform capture rate offers how many waveforms display in a minute, "Dead zone" of oscilloscope is the time of processing and displaying the waveform which have been captured, during the time oscilloscope sacrifices any waveforms. the time of "Dead zone" is far more than "Display zone" for common oscilloscope, which results to signals can not be displayed in most time, so abnormal signals escaped. High capture rate oscilloscope reduces the "Dead zone" time and abnormal signals can be caught fast and accurately.


High capture rate oscilloscope can catch occasional signal		Common capture rate oscilloscope easy to miss the occasional signal


Support various video triggers such as PAL,NTSC,SECAM,720P,1080I,1080P		Connect to flask disk for dynamic recording


240Kpts memory depth		The ScopeSuite of Micsig's software functions include updating, real time control, measurement, storage, dynamic display, record and data analysis.


640 *480 high resolution		Indoor /outdoor display mode


31 auto measurements		Horizontal cursor,vertical cursor,cross cursor


3 types of record modes: multimeter record, oscilloscope measurement record and oscilloscope waveform record.		13 physical measurements such as AC/DC voltage, current,resistance etc.

Model	MS510IT/MS510S	MS520IT/MS520S
Bandwidth(BW)	100MHz	200MHz
Rise time	≤3.5ns	≤1.75ns
Real time sampling rate	single channel :1GSa/s,dual-channels:500MSa/s
Memory depth	single channel :240Kpts,dual-channels:120Kpts
Isolated channel	support
Max waveform capture rate	190,000 wfms/s
Vertical system
Channels	2 oscilloscope channels,1 multimeter channel
Limited bandwidth	20MHz
Coupling modes	DC,AC,GND
Input impedance	parallel 1MΩ±1% with 15pF±3pF
Vertical sensitivity range	5mV/div~50V/div
Vertical resolution	8bits
Max voltage input	600V CAT II 300V CAT III
Floating voltage from CHs to GND	1000V CAT II 600V CAT III
DC vertical gain accuracy	5mV/div~50V/div, 2.0%
Horizontal system
Timebase	2ns/divs~10s/divs
Timebase delay range	-12divs~50s
Timebase accuracy	20ppm
Sample mode	normal average, pk-pk envelope
Dynamic record	max 2 hours
Store waveform	support internal waveform storage and flash disk storage
Trigger system
Trigger types	edge, pulse, logic, vedio (PAL,NTSC,SECAM,720P,1080I,1080P)serial bus(UART,LIN,CAN,SPI,I2C)
Trigger coupling	DC,AC,High-frequency suppression,Low-frequency suppression, Noise suppression
Trigger modes	auto, normal, single
Trigger source	CH1,CH2,external
Trigger inhibition range	200ns~10s
Measurement
Automatic measurements	31 types
Cursor types	horizontal cursor, vertical cursor, cross cursor
Math
Operator	+ , - , * , /
FFT window settings	Rectangular, Hamming, Blackman-Harris, Hanning
Display features
Display screen	5.7 inch TFT LCD touch screen
Resolution	640*480
3D waveform display	not support
Grid of waveform display zone	horizontal 12 divs * vertical 8 divs
Form	YT mode or XY mode
Interpolation method	sin(x)/x
Persist	auto, 100ms~10s or ∞
I/O port
Mini USB2.0	connect to PC
USB2.0	connect to Flash disk
Multimeter
Multimeter type	10 physical measurements ,such as voltage, current, resistance, capacitance, diode , etc
Multimeter accuracy	4 bits
Multimeter display	max, average, min, values with time stamp; relative measurement
Data Logger
Logger content	multimeter measurements, oscilloscope measurements, oscilloscope waveforms
Logger timebase	multimeter measurements,10s/div ~ 20min/div oscilloscope measurements 10s/div ~ 20min/div oscilloscope waveform 100us/div ~ 2min/div
Logger time length	49s~ ∞
Power
Power adapter	input:100-240VAC,50-60HZ,2A; output:12VDC,5A
Battery	capacity:7.4V/6000mAh, Work time:4~5 hours
Work environment
Temperature	-20°C ~ +50°C
Humidity	< 85%RH
Dimension
Size	254mm160mm60mm
Weight	main unit: 1380g (no battery), accessories(standard): 691g,battery(standard): 276g

Siglent SHS800 Series Scopemeter

The SHS800 series is a portable oscilloscope with features normally found only on expensive bench-top instruments. It is ideally suited for field application circuit measurements, electrical debugging, education, scientific research, and quality control. It combines a sophisticated up to 200MHz oscilloscope, a 6000 count multimeter, and a waveform recorder in a portable unit with a bright 5.7” color TFT LCD screen. With a bandwidth of up to200MHz, sampling at 500MSa/s, with a 2Mpts or 32kpt (Model SHS820) sample memory to allow storing, replaying and zooming in on measurements.

The built in data-recorder has up to 18 hours recording time, while the Meter TrendPlot can record multimeter measurement data for as long as 6000 hours at 0.05Sa/s. The Multimeter measures DCV, ACV, DCI, ACI, Resistance, Diode, Capacitance, and Continuity.

Input voltage: input voltage through BNC is up to CATII 300V and CATIII 150V Standard probe: 10X CAT II 400V Optional probe: 10X CAT II 1000V and 10X CAT III 600V Oscilloscope and multimeter safety to CAT II 600V and CAT III 300V.

The SHS800 series offers 32 automatic measurements,3 cursor measure modes, 4 digital filters (low-pass, high-pass, band-pass, band-limit) as well as Math functions +, -, ×, ÷, and X/Y plots, as well as FFT frequency display. Multiple trigger types include video signal settings.

It features USB device for software updates, and USB host capabilities for PictBridge-compatible printers. SHS800 connects to a PC through a USB cable for EasyScope control software and can save/recall waveforms to USB Flash drive. SHS800 can save 2 groups of reference waveforms, 20 groups of setups and 10 groups of waveforms in its internal memory, save setup data, waveform data, waveform interface image, and CSV file to an USB flash drive.

The SHS800 comes with a rechargeable 7.4V 5000mAh Lithium battery pack which lasts up to 5 hours of continuous use, but a DC adapter, 100-240V 50/60Hz 9V 4A DC adapter is also provided.

High-performance oscilloscope
Bandwidth: 60MHz ,100MHz, 150MHz, 200MHz
Real-time sampling rate: 1GS/s
Equivalent sampling rate: 50GS/s
Memory depth: 2Mpt

Data recorder function
7M internal storage, up to 18 hours recording time
USB port, up to 3000 hours recording time
Record, replay and zoom function supported

High precision multimeter
6000 counts display
Accurate measurement of DCV, ACV, DCI, ACI
Accurate measurement of Resistance, Diode, Capacitance, Continuity

TrendPlot
32 measurement trendplot analyzer
Scope: 800k points capacity, more than 24 hours recording time
Meter: 1.2M points capacity 9320 hours recording time at 0.05S/s

Model	SHS806	SHS810	SHS815	SHS820
Bandwidth	60MHz	100MHz	150MHz	200MHz
Rise Time	≤5.8ns	≤3.5ns	≤2.3ns	≤1.7ns
Input Impedance	1MΩ±2%, 18pf±3pf
Real Time Sampling Rate	Single Channel: 1GSa/s, Double Channels: 500MSa/s			500MSa/s
Equivalent Sampling Rate	50GSa/s
Memory Depth	2Mpts			32Kpts
Time Base Range	5 ns/ div – 50s/ div	2.5 ns/ div – 50s/ div
Scan Range	100ms/ div ~ 50s/ div
Vertical Sensitivity	2mV/div – 100V/div(1-2-5 step)
Vertical Resolution	8 bits
Trigger Types	Edge, Pulse, Video, Slope, Alternative
Frequency Counter	6 bits
Connection	USB Device, USB Host
Math	+, -, * , /, FFT
Oscilloscope Trend Plot	800K points

Multimeter Specifications
Display	6000
Item	Range	Accuracy
DC Voltage	60mV - 1000V	±1%±15digit
AC Voltage	60mV –750V	±1%±15digit
DC Current	60mV -10A	±1%±5digit
AC Current	60mV -10A	±1%±5digit
Capacitance	40.00nF	±3%±10digit
Capacitance	400.0nF-400.0uF	±4%±5digit
Resistance	600Ω - 60MΩ	±1%±5digit
Continuity buzzer	<50Ω
Diode	0V~2.0V
Trend plot	1.2M points
Recorder	7M points
Measuring mode	Manual/Auto
General Features
Display	5.7 inch color TFT-LCD, 320*234
Power Supply	Charging/Battery
Power mode	Lithium battery: 7.4V 5000mAh, Battery lasts 5 hours; DC adapter, 100-240V 50/60Hz input, 9V 4A output
Weight	1.5Kg
Dimension	163.2mm×259.5mm×53.3mm

Siglent, Oscilloscope, Tektronix, Agilent, Scopemeter, Owon, Micsig, Tablet Oscilloscope

Siglent SHS 1000 Series Isolated Oscilloscope

The SHS1000 series is a multifunction handheld 2-channel oscilloscope that also includes a full digital multimeter logger and a waveform recorder. Siglent’s patented Isolated Channel technology provides isolation from ground and between channels. With a signal bandwidth of 60MHz or 100MHz, this portable unit with a bright 5.7” color TFT LCD screen can measure at a real-time sample rate of 1GSa/s with a memory depth of 2Mpts, allowing storing, replaying and zooming in on measurements.

The oscilloscope features multiple trigger types (Edge, Pulse, Video, Slope and Alternative), a rise time of less than 5.8ns, vertical sensitivity of 5mV/div – 100V/div and 8 bit vertical resolution. The built-in multimeter of the SHS1000 series can also measure DC/AC voltage, DC/AC current, resistance, capacitance, diode and continuity in many ranges with a display count of 6000. The SHS1000's built in data-recorder has up to 18 hours recording time, while the Meter TrendPlot can record multimeter measurement data for as long as 6000 hours at 0.05Sa/s.

The SHS1000 series offers 32 automatic measurements,3 cursor measure modes, 4 digital filters (low-pass, high-pass, band-pass, band-limit) as well as Math functions +, -, ×, ÷, and X/Y plots, as well as FFT frequency display. Multiple trigger types include video signal settings.

It features USB device for software updates, and USB host capabilities for PictBridge-compatible printers. SHS1000 connects to a PC through a USB cable for EasyScope control software and can save/recall waveforms to USB Flash drive. SHS1000 can save 2 groups of reference waveforms, 20 groups of setups and 10 groups of waveforms in its internal memory, save setup data, waveform data, waveform interface image, and CSV file to an USB flash drive.

The SHS1000 comes with a rechargeable 7.4V 5000mAh Lithium battery pack which lasts up to 5 hours of continuous use, but a 100-240V 50/60Hz 9V 4A DC adapter is also provided. Two 100MHz oscilloscope probes (1 x CAT II 1000V and 1 x CAT III 600V) are included too, as well as two test leads for multimeter measurements.

2-channel device
Includes IsolatedChannel technology that isolates ground and between channels
5.7 inch colour LCD display
60 or 100MHz bandwidth
6000 count multimeter measures DC/AC Voltage, DC/AC current, Resistance, Diode, Capacitance and Continuity
Includes Trendplot, Meter Trendplot and Scope recording functions
Automatic and manual trigger modes
Trigger types: Edge, Pulse, Video, Slope and Alternative
32 automatic waveform measurements, 3 cursor measure modes
Digital filter functions: high pass, band pass, band limit
Mathematical functions: +, -, x, ÷ and FFT
Multiple language user interface
USB device and USB host with PC communication
Rechargeable battery
Ideal for multiple applications including power electronics, industrial power systems, field testing and more

Model	SHS1062	SHS1102
Bandwidth	60MHz	100MHz
Rise Time	≤5.8ns	≤3.5ns
Real Time Sampling Rate	Single Channel: 1GSa/s, Dual Channels: 500MSa/s	Single Channel: 1GSa/s, Dual Channels: 500MSa/s
Equivalent Sampling Rate	50GSa/s	50GSa/s
Memory Depth	2Mpts	2Mpts
Time Base Range	5 ns/ div – 50s/ div	2.5ns/ div – 50s/ div
Scan Range	100ms/ div ~ 50s/ div	100ms/ div ~ 50s/ div
Vertical Sensitivity	5mV/div – 100V/div(1-2-5 order)	5mV/div – 100V/div(1-2-5 order)
Vertical Resolution	8 bits	8 bits
Trigger Types	Edge, Pulse, Video, Slope, Alternative	Edge, Pulse, Video, Slope, Alternative
Frequency Counter	6 bits	6 bits
Connection	USB Device, USB Host	USB Device, USB Host
Math	+, -, * , /, FFT	+, -, * , /, FFT
Oscilloscope Trend Plot	800K points
Meter
Maximum Resolution	6000
DC Voltage	60mV 600mV—1000V	(±1%±15digit) (±1%±5digit)
AC Voltage	60mV 600mV—750V	(±1%±15digit) (±1%±5digit)
DC Current	60.00mA—600mA 6A—10A	(±1%±5digit) (±1.5%±5digit)
AC Current	60.00mA—600mA 6A—10A	(±1%±5digit) (±1.5%±5digit)
Resistance	600Ω—60MΩ	(±1%±5digit)
Capacitance	40nF 400nF--400uF	(±3%±10digit) (±4%±5digit)
Diode	0—2V
Continuity	<50Ω Buzzer sounds
Multimeter Trend Plot	1.2M points

channels from earth ground, between two channels references	Overvoltage Category	Maximum Voltage
	CAT I&CAT II	1000 Vrms
	CAT ?	600 Vrms
between Multimeter input reference and the ground	Overvoltage Category	Maximum Voltage
	CAT I&CAT II	600 Vrms
	CAT III	300 Vrms
Max. input Voltage for BNC	Overvoltage Category	Maximum Voltage
	1x CAT I&CAT II	300 Vrms
	1X CAT III	150 Vrms
	10x CAT I&CAT II	1000 Vrms
	10X CAT III	600 Vrms
Max. input Voltage for Multimeter input port	Voltage port	DC 1000V, AC 750V
	Current port(mA)	AC 250V/600mA
	Current port(A)	AC 250V/10A
Single Channel Common Mode Rejection, typical	>1000:1 50MHz
Channel-to-Channel Isolation	>35 dB

General Feature
Display	5.7 inch color TFT-LCD, 320x234
Power supply	With battery or DC adapter
Power source	Built-in rechargeable lithium battery: 7.4V 5000mAh, Battery persisting 4 hours With DC adapter: 100-240V 50/60Hz input 9V 4A output.
Weight	1.5Kg (3.3lb)
Dimension	163.2mm×259.5mm×53.3mm (6.5” x 10.2” x 2.1”)

Siglent, Phosphor Oscilloscope, Tektronix, Agilent, Owon

Siglent SDS2000 Series Super Phosphor Oscilloscope

The SDS2000 series super phosphor oscilloscope equipped with the maximum 300 MHz bandwidth, 2GSa/s Sampling Rate as well as the design features of memory depth, high capture rate and multi- level intensity grading waveform display, is recognized as an universally applicable digital instrument with advanced technology and high-end performance. With the innovative SPO technology, the SDS2000 series oscilloscope becomes outstanding in the same industry, and even develops a new era in domestic digital oscilloscope industry.

Bandwidth 70MHz,100MHz, 200MHz, 300MHz
Real time sampling rate, Analog channel: 2GSa/s, Digital channel: 500MSa/s (optional)
Provide 2/4 analog channels, 8 digital channels (optional)
Built-in 25MHz function/arbitrary waveform generator(optional)?
A variety of serial protocol trigger and decode functions (IIC, SPI, UART/RS232, CAN, LIN)?
A variety of smart trigger functions (Pattern, Window, Interval, DropOut, Runt)?
Support HDTV trigger?
Support history function and segmented memory (std.up to 80,000 frames)?
Hardware-based zoom function and high speed Pass/Fail function technology?
32 kinds of automatic waveform measurements, support measurement statistics function?
Advanced waveform math operations (FFT, differential, integral, square root)?
Complete connectivity: USB Host, USB Device (USBTMC, PictBridge), LAN(VXI-11), EXT TRIG,? PASS/FAIL,TRIG OUT?
Support SCPI remote control commands?
Multi-language user interface and built-in online help system?
8 inches TFT-LCD(800*480)

Model	SDS2072	SDS2102	SDS2202	SDS2302
	SDS2074	SDS2104	SDS2204	SDS2304
Bandwidth	70MHz	100MHz	200MHz	300MHz
Channels	2/4CH + 1 EXT
Max. real time sampling rate	2Gsa/s
Memory depth	28Mpts
Max. capture rate	110,000wfms/s
Input impedance	1MΩ\|\|20pF,50Ω
Time base range	1.0ns/div~50s/div
	ROLL:100ms~50s/div
Vertical sensitivity	2mV/div~10V/div
Trigger types	Edge, Pulse, Video, Slope, Interval, Runt, Window, Pattern, DropOut, Series Protocol trigger
Decode types	IIC, SPI, UART/RS232, CAN, LIN
MATH operation	A+B, A-B, A×B, A/B, FFT, Diff, Intg, Sqrt
Automatic Measurement	Vpp, Vmax, Vmin, Vamp, Vtop, Vbase, Vavg, Mean, Crms, Vrms, ROV, FOV, RPRE, FPRE, Rise time, Fall time, Freq, Period, + Wid, - Wid, + Dut, - Dut, BWid, Phase, FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF
External storage	Bitmap save, CSV save, Waveform save, Setup save
Interface	USB Host(support USB-GPIB), USB Device, LAN, EXT TRIG, Aux(TRIG OUT/Pass/Fail)
Display	8 inches TFT-LCD(800*480)
Max. input voltage	±400V(DC+VppAC), CATI, CATII
Power supply	AC 100-240V, 45-440Hz, 50VA Max
Dimensions	352mm112mm224mm
Weight	3.4kg(2CH), 3.5kg(4CH)

YOKOGAWA 8 CHANNEL OSCILLOSCOPE, TEKTRONIX, LECROY, SIGLENT, OWON

Yokogawa DLM4000 Series Mixed Signal Digital Oscilloscopes

Overview
The DLM4000 Series Oscilloscope is unique to the industry, providing eight channel mixed signal suitable to test and debug applications in embedded systems, power electronics, mechatronics and automotive sectors. Available in both 350MHz and 500MHz models, the 2.5 GSa/sec DLM4000 features eight analog input channels.

Features

Built-in user friendly Graphical help. No need to consult the user's manual.
Multiple language support: English, Japanese, Chinese, Korean, Italian, French, German, Spanish, Russian.
Multi-Color LED display.
Statistical Analysis.
Trend and Histogram of waveform parameters.
Waveform monitoring on a PC.
Data transfer to a PC.
GO/NO-GO judgement using polygon zoning or waveform parameters is possible without programming.
29 different parameters such as Min, Max, Mean and Standard deviation from multiple acquisitions.
Power supply analysis function.
Extra Deep Memory (125 Mega-Points). Super long record lengths with ease.

The eight input channels features Flex MSO which converts to an 8-bit logic analyzer at the push of a button, with sixteen additional logic analyzer inputs as an option, making it into a 24-bit logic analysis system.

Advanced measurement and analysis features such as power analysis and serial-bus analysis, digital filtering, user-defined math, and super long record lengths (up to 125 Mega Points) make the DLM4000 a super powerful engineering tool. High-resolution 12.1 inch LCD display, compact landscape format, ergonomic and friendly user-interface makes this series easy to use.

Model
DLM4038 350Mhz Standard 8 analog channels or 7 analog channels + 8-bit logic
DLM40538 500Mhz 8 analog channels + 16-bit logic or 7 analog channels + 24-bit logic

Download
DLM4000 Specifications (PDF)
(documents are in PDF format and will open in a new window) 3.92MB

Yokogawa, Oscilloscope, Scopecorder, Data Acqusition, Tektronix, Fluke, Agilent, owon, micsig, osiloskop

Yokogawa DL850 Series ScopeCorder

Measure and analyze a wealth of signals in real-time and speed up development and fault finding.
The DL850E ScopeCorder is a powerful portable data acquisition recorder and oscilloscope that can capture and analyze both transient events and trends up to 200 days. Using flexible modular inputs it combines measurements of electrical signals, physical (sensors) and CAN / LIN serial buses and is able to trigger on electrical power related and other calculations in real-time.

Flexible and Swappable Input Modules With Built-in Signal Conditioning

Choose from 17 types of input module and install up to 8 in a ScopeCorder at a time to configure a ScopeCorder up to 128 channels.

Voltage & Currents
Sensor Outputs
Temperature, Vibration/Acceleration, Strain, Frequency
Logic Signals & CAN / LIN

Precise Measurement of Fast Switching Signals Even in the Harshest Environments

Individually isolated and shielded input channels provide high-resolution and high sample rates.

Real-Time Evaluation of Dynamic Behavior within Power Applications

Trend calculations such as active power, power factor, integrated power, harmonics and more using the new power math option.

A Trustworthy Measurement Platform for Durability Testing

Measurement recording up to 200 days to the large 2 Gpoint acquisition memory, the internal hard disk and/or PC hard disk.

Reduce Time Spent on Fault Finding

Capture transient signals even during long term measurements using powerful triggers and unique features such as dual capture & history memory.

Fast and Large Acquisition Memory

A ScopeCorder is equipped with a large & fast acquisition memory up to 2Gpoint and enables high sample rates of up to 100MS/s on multiple channels simultaneously. This is ideal for viewing multiple inverter switching outputs simultaneously.

Standard memory 250MPoint
Expanded memory 1GPoint (/M1 Option)
Expanded memory 2GPoint (/M2 Option)

Giga Zoom Engine II

Zoom into 2 Billion samples in just a blink of the eye. Each ScopeCorder is equipped with the revolutionary Giga Zoom Engine II, a powerful processor designed for optimizing access to data seamlessly. It is possible to activate 2 zoom windows while displaying the entire original signal.

Capture and record detailed waveforms from milliseconds up to months

A ScopeCorder provides a wide variety of unique acquisition features to handle small or large amounts of data. Therefore it can perform multi-channel measurements for longer measurement periods while still being able to precisely capture transient events with the highest detail.

Reduce time spend on fault finding or transient analysis - simple & enhanced triggers

Having the possibility to set individual triggers on multiple channels provides the power to investigate what causes a particular transient event. Moreover, the availability of a large acquisition memory, and thus longer measurement time, helps the analysis of the effect of such an event on other parts of the application.

Wave Window Trigger
The ideal trigger for AC power line monitoring. Easily capture voltage sags, interfering impulses, phase shifts or drop outs.

Action on trigger
Leave a ScopeCorder unattended and automatically save the waveform to a file or send an email for notification of a trigger event.

Capture High-Speed Transients During Long Term Recording - Dual capture
To visualize long term trends for durability testing, data is typically acquired at lower speed sample rates. On the other hand, suddenly-occurring transitional phenomena have to be captured at high-speed sample rates and detail to be able to investigate the event. The "Dual Capture" function uniquely resolves these conflicting requirements by recording at two different sampling rates.

Set waveform triggers and capture 5,000 high-speed transient events at sample rates up to 100 MS/s, while at the same time continuously record trend measurements at up to 100kS/s.

Recall waveform events - History Memory
When an abnormal phenomenon is spotted during a repetitive high speed measurement, the anomaly has often already disappeared from the screen by the time the measurement is stopped. With a ScopeCorder the "History" function is always active and automatically divides the available acquisition memory in up to 5,000 "history waveforms".

These history records are easily accessible and can be displayed simultaneously after measurement is stopped. Using condition-based searches inside the history memory, users can quickly isolate individual waveforms records. Once the required waveforms have been identified they can be used for further analysis.

Cursor Measurement
Using cursors is a quick and easy method to measure waveform parameters on the screen. Available cursors are horizontal, vertical, marker, degree or combined horizontal & vertical.

Automatic Waveform Parameter Measurement
The parameter measure function is the most precise method for automatically calculating any or all of the 28 different waveform parameters such as, amplitude, peak to peak values, RMS, rise time, frequency and more.The internal time clock (date and time) can be synchronized and adjusted across multiple units. Applications are likely to include synchronizing the ScopeCorder at a windmill farm, finding faults in power grids, and more.

Cycle Statistics
With this powerful analysis function, the ScopeCorder measures selected parameters individually for each waveform cycle and provides statistical information which can easily be saved to a file. By selecting maximum or minimum values from the results, the instrument can automatically zoom into the selected waveform cycle for further analysis, potentially saving additional data analysis time.

Real-time hard disk recording
Use a ScopeCorder as a measurement platform for simple durability testing up to 200 days. Realtime hard disk recording enables measurement data to be streamed directly to either a built-in hard drive (/HD0 option) or via the eSATA interface (/HD1 option) to an external hard drive.

Measurement examples to internal or external Hard Disk

Continuous PC based data acquisition - ScopeCorder Acquisition Software
Especially for longer duration or surveillance testing the ScopeCorder comes with an easy to setup acquisition software. The software enables continuous data recording to a PC hard drive. When using the software in free run mode there are virtually no restrictions in recording time and/or file size. Just click the start button to immediately start measurements!

The Setup Wizard Makes It Easy
Guided by four screens, the Setup Wizard easily guides you through the necessary settings for configuring the acquisition system such as measurement settings, data save and display options.

GPS Time Synchronisation
The ScopeCorders internal clock and the sampling clock can be time synchronized with a GPS clock reference using the /C20 or /C30 option. This allows multiple units to be synchronised in order to combine measurements from different remote locations with most accurate timing. Applications are likely to include synchronising the ScopeCorder measurements at a windmill farm, finding faults in power grids and railway applications. Measurement files from multiple ScopeCorder units can be merged into one measurment overview using Xviewer software.

GPS Interface (/C30 option)
A GPS antenna (included with the option) can be directly connected to the ScopeCorder side panel.
The instruments time clock and the sampling clock will be synchronized to the GPS clock with ±200ns accuracy.

IRIG interface (/C20 option)
An IRIG time code signal generated by an external GPS clock device (not included) can be offered to the ScopeCorder.

Powerful Real-Time Calculations and Analysis Functions
By default the ScopeCorder is equipped with a set of basic arithmetic mathematical functions such as addition, subtraction, division, multiplication, fast Fourier transformation and other computations. Furthermore to really enrich the measurement and analysis capabilities of a ScopeCorder, several real-time options are available.

Real-Time Measurement of Electrical Power - /G5 option
Trend calculations such as active power, power factor, integrated power and harmonics, using a dedicated Digital Signal Processor (DSP) that is able to calculate and display up to 126-types of electrical power related parameters in real-time. This enables the user to display raw waveform signals such as voltages and currents along with power calculated parameters and even the capability to trigger on all of them. Data updating rate up to 100kS/s. Trend waveforms of each order of harmonics, bar-graphs and vector displays can be displayed. Both RMS and Power analysis modes are available. Besides the powerful power calculations, the /G5 option also contains all the functionality of the /G3 option.

Real-Time Mathematical Computations and Digital Filtering - /G3 option
Armed with a dedicated digital signal processor the ScopeCorder can perform mathematical calculations such as arithmetic operators with coefficients, integrals and differentials, and higher order equations on acquired measurement data. The results of these calculations are displayed during waveform capture in real-time. In addition to mathematical operators, steep digital filters can also be selected to isolate or trigger on the amplitude of certain frequency components.

User defined computations - /G2 option
With user defined computations it is possible to create equations using a combination of differentials and integrals, digital filters, and a wealth of other functions. Moreover it is possible to perform various types of FFT analysis using two FFT windows. In applications such as vibration and shock tests, you can easily evaluate abnormal vibrations while simultaneously measuring other signals.

Application Example | With FFT

The ScopeCorder Vehicle Edition is designed for engineers working in the automotive and railway industry. A common measurement challenge is to combine measurements of electrical signals, physical performance parameters, indicated by sensors, together with CAN- or LIN-bus data transmitted by the powertrain management system. A ScopeCorder Vehicle Edition addresses this requirement by providing a thorough insight into the dynamic behavior of the electromechanical system. The result is a considerable saving of time compared to other approaches such as analysis on a PC or the use of other software.

CAN and LIN Bus Monitoring
Use a ScopeCorder to decode the CAN or LIN-Bus signals and display information on physical data like engine temperature, vehicle speed and brake-pedal position as analog waveforms and compare this with the data coming from real sensors.

Symbol Editor

The symbol editor is a software tool which makes it possible to define which physical values from the CAN- or LIN-bus data frame have to be trended as waveform data on the display of the ScopeCorder. The Symbol Editor can accept vehicle-installed network definition files (CAN DBC, LIN LDF).

Battery Powered Operation - /DC option
In addition to AC power, it is also possible to take the ScopeCorder Vehicle Edition in a vehicle and power the unit from the vehicle's DC battery. The DC power option allows AC and DC power supplies to be used together to ensure a highly reliable power source. If the AC power goes down, the DL850EV instantly switches to the DC supply without interrupting the measurement.

DC power (10 - 18V)
AC power (100 - 120V / 200 - 240V)

Flexible operation and a variety of connection interfaces
A ScopeCorder has been designed to grant users access to functionality in the field quickly and easily using the front panel menu buttons. For users that prefer workbench operation it is possible to connect a USB mouse or keyboard.

Front View

Left Side View

Right Side View

Owon, Osiloskop, test ve mühendislik, Oscilloscope, Keysight, tektronix

Owon RDS1021i Pen type Oscilloscope

- 25MHz bandwidth - 100MS/s sample rate - 5K record length - FFT function - Human engineering design - Multi- action mode via creative trackball - Multi- trigger option : edge, slope, and pulse - 5mV micro signal supported - USB bus powering, and optional USB isolated function - Easy portability, pocket accommodated

Bandwidth	25MHz
Sample Rate	100MSa/s
Horizontal Scale (s/div)	5ns/div - 100s/div, step by 1- 2 - 5
Rise Time	≤14ns
Record Length	5K
Input Coupling	DC, AC , and GND
Input Impedance	10MΩ±2% (X 10), 1MΩ±2% (X1)
Input Capacitance	20pF±5pF
Max Input Voltage	400V ( PK - PK) (DC + AC, PK - PK)
DC Gain Accuracy	±3%
DC Accuracy (average)	average≥16 : ±(3% reading + 0.05 div) for ?V
Analog Bandwidth	25MHz
Probe Attenuation Factor	1X, 10X
LF Respond (AC, -3dB)	≥10Hz
Interpolation	Sin(x)/x
Displacement	±10 divisions
Interval (?T) Accuracy (full bandwidth)	Single : ±(1 inter val time + 100ppm × reading + 0.6ns), Average>16 : ±(1 inter val time + 100ppm × reading + 0.4ns)
Vertical Resolution (A/D)	8 bits
Vertical Sensitivity	5mV/div - 5V/div
Trigger Type	Edge, Pulse, Slope
Trigger Mode	Auto, Normal, Single
rigger Level	±5 divisions from screen center
Acquisition Mode	Sample, Peak Detect and Average
Cursor Measurement	? V and ?T between cursors
Automatic Measurement	Vpp, Vavg, Vrms, Freq, Period, Vmax, Vmin, Vtop, Vbase, Vamp, Overshoot, Preshoot, Rise Time, Fall Time, +Width, -Width, +Duty, -Duty
Waveform Math	FFT
Communication Interface	USB2.0
Dimension (W×H×D)	150× 20× 18(mm)
Weight (without package)	0.27kg

Hızlı Bilgi Formu

Oscilloscope kategorisine ait diğer ürünler

Application

- 2 in 1 (DSO + LA) - 8 inch color LCD - USB data transmission supported - 20 group automatic measurement options

Application

Model

Bandwidth

Real time Sample Rate

Rise Time

Memory Depth

Channel

Touch operation

Serial bus trigger

Max waveform capture

-(can be upgraded to 50K wfms/s)

-(can be upgraded to 50K wfms/s)

Model

MS310IT

MS320IT

Vertical system

Horizontal system

Trigger system

Measurement

Math

Display Features

I/O Port

Multimeter

Data Logger

Power

Work environment

Dimension

Model

MS207T

MS210T

MS215T

MS220T

Vertical system

Horizontal system

Trigger system

Measurement

Math

Display Features

I/O Port

Multimeter

Data Logger

Power

Work environment

Dimension

Model

Bandwidth

Real time sampling rate

Rise time

Memory depth

Max capture rate

Channel

Touch operation

Serial bus trigger

Serial bus decode

Model

MS510IT/MS510S

MS520IT/MS520S

Vertical system

Horizontal system

Trigger system

Measurement

Math

Display features

I/O port

Multimeter

Data Logger

Power

Work environment

Dimension

Flexible and Swappable Input Modules With Built-in Signal Conditioning

Precise Measurement of Fast Switching Signals Even in the Harshest Environments

Real-Time Evaluation of Dynamic Behavior within Power Applications

Fast and Large Acquisition Memory

Reduce time spend on fault finding or transient analysis - simple & enhanced triggers

Cursor Measurement Using cursors is a quick and easy method to measure waveform parameters on the screen. Available cursors are horizontal, vertical, marker, degree or combined horizontal & vertical.

CAN and LIN Bus Monitoring Use a ScopeCorder to decode the CAN or LIN-Bus signals and display information on physical data like engine temperature, vehicle speed and brake-pedal position as analog waveforms and compare this with the data coming from real sensors.

- 2 in 1 (DSO + LA)
- 8 inch color LCD
- USB data transmission supported
- 20 group automatic measurement options

Cursor Measurement
Using cursors is a quick and easy method to measure waveform parameters on the screen. Available cursors are horizontal, vertical, marker, degree or combined horizontal & vertical.

CAN and LIN Bus Monitoring
Use a ScopeCorder to decode the CAN or LIN-Bus signals and display information on physical data like engine temperature, vehicle speed and brake-pedal position as analog waveforms and compare this with the data coming from real sensors.